Appearance: NewFunctionality: Not WorkingDescription:============As pictured, a QuantumProDrive 1080s. Recognized by the SCSI bios, but machine will hang on boot – soldas-is.About Us:=========The ComputerPreservation Group is dedicated to the preservation of historical computers. Tohelp fund ongoing operations, select items are made available. Thank you foryour support!Warranty andReturns:=====================This product isbeing sold AS-IS without any warranty. Returns are not accepted. To ensure thatthis is the right product for your needs, we’re happy to answer any questions. Shipping:=========- Local pickup isalso available at no cost.- Most orders placedbefore 9am will ship the same day.Stock#:10045E M P I R E 1 0 8 0S QUANTUMNative| Translation------+-----+-----+-----Form 3.5"/SLIMLINE Cylinders 2874|| |Capacityform/unform 1080/ 1232 MB Heads 8| ||Seek time / track9.5/ 1.8 msSector/track | ||Controller SCSI3 SI/FA PrecompensationCache/Buffer 512 KB LOOK-AHEAD Landing ZoneData transferrate MB/S int Bytes/Sector 512 10.000 MB/S ext SYNCRecordingmethod RLL 1/7 operating | non-operating-------------+--------------Supply voltage 5/12 V Temperature *C 55| -40 75Power: sleep W Humidity %5 95 | 5 95 standbyW Altitudekm -0.061 3.000| -0.305 12.000 idle 6.0 W Shock g10 | 60 seek 7.3 W RotationRPM 5400 read/write 7.5 WAcoustic dBA 35 spin-up W ECCBit 112,REED SOLOMON MTBF h500000 WarrantyMonth 60Lift/Lock/Park YES Certificates CSA,FCC,TUV,UL1950,VDELayoutQUANTUM EMPIRE540/1080S PRODUCT MANUAL 81-103983-01/03 1993/1994 +---------------------------------------------------------+ |+++++++++++++ |XX J1 |+++++++++++++JP1 |XX |F1+|XX ||||XX I |AUGUST 1993 ++|XXN ||XX T |J13+|XX E |++|XX R ||XX F ||XX A ||XX C ||XX E | |X1 ++LED| ++|XX J3 ||XX Power +---------------------------------------------------------+ 1+---------------------------------------------------------+ |++++++++++++ ++|XX J1 |++++++++++++J9 |||XX | |||XX ||||XX I |JUNE 1994++|XX N |xxJ13XX T | xxTE|XX E ||XX R |++|XX F |J12|||XX A |+-+ Alternate RExx |||XXC || | Address|||XX E || | Connector ++|X1 |1-+| ++J5|XX J3 1+LED|XX Power+---------------------------------------------------------+ 1JumpersQUANTUM EMPIRE1080/540S PRODUCT MANUAL 81-103983-01/03 1993/1994 Jumper Setting==============x = Jumper set atfactory AUGUST 1993---------------------------------A1---------+ +-+-++-+-+-+-+-+A0-+-+-A2 |XX J1 |x|x| |x| |x| | | | | | | JP1 |XX +-+-+ +-+-+-+-+-++-+-+-+ |XX | | | | | | |+-+-+ |XX(FactoryI/O---+ | | | | | | + SCSI ID RESERVED)INT ----+ | | | | +------ WS | | | +-------- EP | | +---------- PF(Factory RESERVED) | +------------ TE +-------------- SS(Factory RESERVED)x = FACTORYRESERVED! JUNE 1994 --------------------------------A1--------+ +-+-+ +-+-+-+-+A0-+-+-A2 |XX J1 |x|x| |x|x| | | | | | | JP1 |XX +-+-+ +-+-+-+-+ +-+-+-+ |XX | | | | | |+-+-+ |XX(FactoryI/O---+ | | | | | + SCSI ID RESERVED)INT ----+ | | | +------ WS | | +-------- EP | +---------- PF(Factory RESERVED) +------------ SS(Factory RESERVED)x = FACTORYRESERVED!On the Drive's PCBA,there are eight pairs of jumper pins, usuallycalled jumpers, that control the drive'soperation. (In addition,numerous options controlled by SCSI commandsaffect the operation ofthe drive.) Four of these jumper pins, PF, SS,INT, and I/O, are re-served for factory use. However, you mightneed to change some of theother six jumpers to configure the driveproperly. These user-configurable jumpers include: (* RE(J2) (JUNE 1994) - ROM enable) * TE- Termination Enable Jumper * EP- Enable Parity Jumper * WS- Wait/Spin Jumper * A2,A1,A0 - SCSI-Bus Identification Jumpers * J13- SCSI Termination Power JumperWhen you change anyjumper setting but J13, the new setting is ineffect the next time the drive is powered on.J13 immediately affectsthe SCSI terminator power source.+---------+-----------+--------------------------------------------+ | Jumper| Setting | Description | +---------+-----------+--------------------------------------------+ |RE(J2)| OPEN x | Firmware is executed from FLASH memory | |JUNE 1994| CLOSED | Firmware is executed from aninternal | || | microprocessorROM |+---------+-----------+--------------------------------------------+ |TE | OPEN | Termination Disabled | || CLOSED x | TerminationEnabled |+---------+-----------+--------------------------------------------+ |EP | CLOSED x | Parity checking enabled | || OPEN | Parity checkingdisabled | +---------+-----------+--------------------------------------------+ |WS | OPEN x |Wait/Spin disabled| || CLOSED | Wait/Spinenabled |+---------+-----------+--------------------------------------------+ | A2,A1,A0|- | These jumpers are used in combinationto | || | determine thedrive's SCSI ID. |+---------+-----------+--------------------------------------------+ |J13 | CLOSED x | SCSI terminator power supplied by the host| || OPEN | SCSI terminatorpower supplied by the drive|+---------+-----------+--------------------------------------------+JUNE 1994 RE(J2) ROMEnable Jumper-----------------------------------The ROM Enable jumper determines the drivecode execution mode. WhenRE is off (default), the drive firmware isexecuted from FLASHmemory. When the drive is shipped with RE ON,the firmware isexecuted from an internal microprocessor ROM.TE TerminationEnable Jumper----------------------------One of the requirements of the SCSI bus isthat it be terminated withproper termination resistors. If more than onehard disk device isconnected to the host, the last one must beterminated. The TE(Termination Enable) jumper, when installed,connects terminatingresistors to the SCSI bus. With the TE jumperoff, no resistors areconnected.EP Enable ParityJumper------------------------The Enable Parity (EP) jumper controls paritychecking across theSCSI bus. With parity checking enabled, thedrive performs paritychecking. With parity checking disabled, thedrive continues togenerate parity information, but not performparity checking.At the factoryQuantum configures the Empire 540/1080S hard diskdrive with parity enables; that is, with ajumper installed acrossthe pins labeled EP. To disable paritychecking, remove the jumperfrom the EP pins.WS Wait/Spin Jumper--------------------With the Wait/Spin (WS) jumper disabled, at apower on or reset, thedrive motor starts to spin automatically, andthe drive preparesitself to perform read or write operationswithout the need for astart command. At a power or reset, with theWait/Spin jumperenabled, the host must send a START/STOP UNITcommand to activate thedrive motor for read or write operations. Inaddition, with the W/Sjumper enabled, the drive performs powersequencing to prevent anoverload of the host's power supply due tosimultaneous, peak start-up current demands from multiple devices.At the factory,Quantum configures the Empire 540/1080S hard diskdrive with the Wait/spin jumper disabled; thatis, without a jumperinstalled across the pins labeled WS. Toenable the Wait/spin jumper,install a jumper across the WS pins.A2/A1/A0 SCSI-BusDevice Identification----------------------------------------Used in combination, the jumper settingsacross A2, A1, and A0 de-termine the Empire 540/1080S hard disk drive'sSCSI-bus deviceidentification (SCSI ID). By default, Quantumconfigures the drivewith a SCSI ID of six; that is, with jumpersinstalled across thepins labeled A2 and A1, and no jumperinstalled across the pinslabeled A0. +----------+-----------------------+ | SCSI ID| Jumpers | || A2 |A1 | A0 | +----------+-------+-------+-------+ |0 | OPEN | OPEN| OPEN | |1 | OPEN | OPEN| CLOSED| |2 | OPEN | CLOSED| OPEN | |3 | OPEN | CLOSED| CLOSED| |4 | CLOSED| OPEN | OPEN| |5 | CLOSED| OPEN | CLOSED| |x6 | CLOSED| CLOSED| OPEN | |7 | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+The SCSI bus supports up to eigth devices,including the host system.A device's identification number determinesits priority and must beunique in the system.JUNE 1994 J12Alternate Address Connector-----------------------------------------When external SCSI ID addressing is used, alljumpers installedacross the pins labeled A2, A1, and A0 at J9must be removed. J12 Pin Assignment +---+-------------+ |PIN| Power Line | || Designation | +---+-------------+ | 1 | Ground | | 2 | A2 | | 3 | A1 | | 4 | A0 | | 5 | N/C | +---+-------------+InstallQUANTUM EMPIRE540/1080S PRODUCT MANUAL 81-103983-01/03 1993/1994 Notes on installation=====================Orientation-----------The mounting holes on the Empire 540/1080Shard disk drive allow thedrive to be mounted in any orientation.Mounting--------Drive mounting orientation, clearance, andventilation requirementsare described in the following subsections.For mounting, #6-32 UNCscrews are recommended. To avoid stripping themounting-hole threads,the maximum torque applied to the screws mustnot exceed 8 inch-pounds.Clearance---------The printed-circuit board assembly (PCBA) isvery close to themounting holes. Clearance from the drive toany other surface -except mounting surfaces - must be 2.6millimeters (0.10 inches)minimum. The specified screw length allowsfull use of the mounting-hole threads, while avoiding damaging orplacing unwanted stress onthe PCB.Ventilation-----------The Empire 540/1080S hard disk drives operateswithout a cooling fan,provided the ambient air temperature does notexceed 131*F (55*C).J3 DC Power Connector---------------------The drive's DC power connector (J3) is mountedon the back edge ofthe Printed-Circuit Board (PCB). +----------+ |43 2 1| +----------+Recommendedconnectors and their numbers:4-pin connector: AMPP/N 1-480424-0 or equivalentLoose-piececontacts: AMP P/N 60619-1 or equivalent (20-14 ga.)Strip contacts: AMPP/N 61117-1 or equivalent (20-14 ga.) pin 1+12 VDC pin 2+12 Volts Return (Ground) pin 3+ 5 Volts Return (Ground) pin 4+ 5 VDCNote:Labels indicate the pin numbers on theconnector. Pins 2 and 3(ground returns) are connected on the drive.J5 LED Connector----------------The drive's LED connector is mounted on theback edge of
